N16GPCessna U206G

On September 4, 2017 about 1430 Alaska daylight time, an amphibious float-equipped Cessna U206 airplane, N16GP, sustained substantial damage while attempting to depart the water at Trident Basin Seaplane Base (T44), Kodiak, Alaska. The airplane was registered to and being operated by the pilot as a 14 Code of Federal Regulations Part 91 visual flight rules flight. The airline transport pilot and three passengers were not injured. Marginal visual meteorological conditions existed and no flight plan had been filed.

According to the pilot during the takeoff run, the airplane encountered small swells and began to lose speed, while simultaneously pitching forward. In an effort to correct for the forward pitching moment, the pilot applied full aft elevator. Shortly thereafter, he aborted the takeoff, but the airplane continued to pitch forward when it was struck by a larger swell. The right forward float strut fractured and the airplane rolled to the right, which resulted in substantial damage to the right wing's lift strut. An initial examination of the airplane by the pilot revealed that the left nose wheel was partially deployed with the landing gear handle in the up position.

A pilot rated witness reported that the accident pilot was talking to several pilots, prior to boarding the airplane, the morning of the accident and specifically asked him "what do you think?" and "which way to go?". He went on to state that one of the options, rather than the typical north departure, was to use "The Cut", which is an easterly departure through a break between the islands. He said this worked as long as the aircraft was airborne before exiting the protected area, as ocean swells were encountered on the other side of the islands.

Another pilot rated witness reported that he leaned out his office door and watched as the accident pilot started his water run. He said his initial thought was that the airplane "must be really heavy" because it took a very long time for the airplane to accelerate onto the step. As the airplane disappeared through "The Cut", he saw the wings start rocking up and down, as the airplane, still on step, encountered the ocean swells on the other side.

A third pilot rated witness reported that he observed the accident airplane begin its water run. He stated that the airplane was in the plow for an estimated 1,100 ft, prior to accelerating onto the step. The airplane then went through the "The Cut" where it encountered about 8-foot-tall ocean swells, and disappeared. He continued to hear the airplane's engine operating at full power for about 15 seconds before it abruptly stopped. He then jumped in his skiff and motored through "The Cut" to the accident site to assist with the rescue of the airplane and its occupants.

A fourth pilot rated witness who aided in the recovery of the airplane the day of the accident reported wind from the east at 15 to 20 knots, 1 to 1 ½ ft seas, with 6 to 8-inch swells. He also stated that there was no evidence of a hydraulic oil leak on the water as the airplane was towed back to the docks at T44.

Neither the pilot, nor any of the multiple witnesses reported the airplane yawing about its vertical axis during the takeoff run.

Photos of the accident airplane taken during the rescue indicate rough water near the accident site with large ocean swells.

The coastal waters forecast for Chiniak Bay on September 4, called for seas of 9 ft, with wind out of the southeast at 25 knots and rain, and a Small Craft Advisory had been issued.

The closest weather reporting facility was Kodiak Airport (PADQ), Kodiak, Alaska, about 4.5 miles southwest of the accident site. At 1428, a METAR from PADQ was reporting, in part: wind 100° at 15 knots; visibility, 4 statute miles, mist; clouds and ceiling, scattered clouds at 1,000 ft, overcast clouds at 3,100 ft; temperature, 54° F; dew point 54° F; altimeter, 29.59 inches of Mercury.

The airplane was equipped with EDO 696-3500 amphibious floats. The hydraulic lines that service the landing gear are routed through the hollow float struts to their attach points on the deck of the floats.

The mechanic who removed the airplane from the water the day after the accident reported that all three of the right float struts were separated completely from their attach points and the hydraulic lines servicing the landing wheels were severed.

A postaccident examination of the airplane revealed that the left and right mechanical portion of the landing gear retraction system was not rigged correctly, and the amphibious float cable loops were set to about a 17-pound tension load. No evidence of a hydraulic leak was present inside the amphibious floats or the fuselage.

The EDO Model 696-3500 Service and Maintenance Manual states in part: "Rig the cable loop to a 75 – 125-pound tension load."

The book, How To Fly Floats, published by EDO Corporation, Rough Water Take-offs states in-part: "When possible, take-offs in rough water should be avoided. Before attempting a rough water take-off, do some reconnaissance of the area first. You may happen to find more favorable surface conditions nearby. Pay special attention to any severe swell conditions that may exist and keep an eye out for swells produced by moving boat traffic. There is a very good possibility that severe damage can be done to either the floats, the attachment gear or the aircraft in big swell conditions."