N2452CPiper PA-38-112

On February 22, 2017, about 0956 eastern standard time, a Piper PA-38-112, N2452C, was destroyed when it impacted terrain in East Haven, Connecticut, during the initial climb from Tweed-New Haven Airport (HVN), New Haven, Connecticut. The flight instructor was seriously injured, and the student pilot was fatally injured. The airplane was operated by American Flight Academy as an instructional flight conducted under the provisions of Title 14 Code of Federal Regulations Part 91. Visual meteorological conditions prevailed, and no flight plan was filed for the local flight.

According to an air traffic control transcript provided by the Federal Aviation Administration (FAA), the airplane completed four touch-and-go landings on runway 20, a 5,600-ft-long by 150-ft-wide asphalt runway. At 0955:43, during initial climb after the fourth landing, one of the pilots declared an emergency and stated, "mayday mayday mayday we're going to land on the other runway." The controller cleared the airplane to land, and no further communications were received from the pilots. Another flight instructor, who was also flying in the HVN airport traffic pattern at the time of the accident, stated that he heard the emergency transmission and could hear the airplane's stall warning horn in the background during the transmission. According to a witness, the airplane then spun to the left, descended in a nose-down attitude, and impacted terrain about 1,000 ft southeast of the departure end of runway 20. Review of radar data did not reveal any targets that could be correlated with the accident airplane during the initial climb in which the accident occurred.

The flight instructor was subsequently interviewed at a hospital by an FAA inspector. The flight instructor told the FAA inspector that he remembered practicing airwork and then returning to the airport to practice touch-and-go landings, but he did not recall the accident sequence.

The flight instructor held a commercial pilot certificate with ratings for airplane single-engine land, airplane multi-engine land, and instrument airplane. He also held a flight instructor certificate with a rating for airplane single-engine. His most recent FAA first-class medical certificate was issued on November 14, 2014. Review of the flight instructor's logbook revealed that he had accumulated a total flight experience of about 236 hours, of which 12 hours were in the same make and model as the accident airplane. The flight instructor had flown about 28 hours during the 30-day period preceding the accident.

Review of the student pilot's logbook revealed that he had accumulated a total flight experience of about 17 hours of which 15 hours were in the same make and model as the accident airplane. The student pilot had not yet flown solo.

The two-seat, low-wing, fixed tricycle-gear airplane was manufactured in 1978. It was powered by a Lycoming O-235, 112-horsepower engine, equipped with a two-blade, fixed-pitch Sensenich propeller.

Review of the airplane's logbooks revealed that, at the time of the accident, the airframe had accumulated about 8,473 total hours of operation, and the engine had accumulated 2,508 hours since major overhaul. The airplane had been operated for 78 hours since its most recent 100-hour inspection, which was completed on September 30, 2016. Review of maintenance records did not reveal any prior anomalies with the airplane's fuel selector. Review of the airplane maintenance manual revealed instructions, applicable to 100-hour inspections, for the fuel selector to be inspected for condition, security, and operation. According to the instructions, if the fuel selector valve binds, sticks, or is otherwise difficult to operate, the fuel selector valve should be lubricated. Specifically, the insert, position washer, and "O" rings should be lubricated.

The reported weather at HVN, at 0953, included wind from 210° at 5 knots, visibility 10 statute miles, and an overcast ceiling at 7,500 ft.

The two-seat, low-wing, fixed tricycle-gear airplane was manufactured in 1978. It was powered by a Lycoming O-235, 112-horsepower engine, equipped with a two-blade, fixed-pitch Sensenich propeller.

Review of the airplane's logbooks revealed that, at the time of the accident, the airframe had accumulated about 8,473 total hours of operation, and the engine had accumulated 2,508 hours since major overhaul. The airplane had been operated for 78 hours since its most recent 100-hour inspection, which was completed on September 30, 2016. Review of maintenance records did not reveal any prior anomalies with the airplane's fuel selector. Review of the airplane maintenance manual revealed instructions, applicable to 100-hour inspections, for the fuel selector to be inspected for condition, security, and operation. According to the instructions, if the fuel selector valve binds, sticks, or is otherwise difficult to operate, the fuel selector valve should be lubricated. Specifically, the insert, position washer, and "O" rings should be lubricated.

No debris path was observed, and the wreckage came to rest upright in a marsh, oriented on a near north magnetic heading. Both wings remained attached to the airframe, and the ailerons and flaps remained attached to their respective wings. The ailerons were about neutral, and the flaps were partially extended. The fuel caps remained secured to their respective wing fuel tanks, and, although both wing fuel tanks were breached during impact, several gallons of fuel remained in each wing. The right wing was buckled. The left wing exhibited more leading edge damage than the right wing, and its wingtip was bent upward, consistent with the left wing impacting terrain before the right wing.

The empennage was curled up and to the left. The horizontal stabilizer, vertical stabilizer, rudder, and elevator remained intact. Flight control continuity was confirmed from all flight control surfaces to the cockpit area. Examination of the elevator trim wheel revealed that the elevator trim cable remained wrapped around the spool twice, which equated to an elevator trim position between neutral and full nose up. Examination of the cockpit revealed that the seatbelts and shoulder harnesses remained intact. The throttle and mixture levers were in the forward position, and the magnetos were selected to both. The fuel selector handle was found positioned to the right main fuel tank.

The engine was partially buried in mud but remained attached to the airframe, and the propeller remained attached to the engine. The two propeller blades did not exhibit rotational damage. The wreckage was further examined at a recovery facility, and the engine was separated from the airframe for the examination. The valve covers were removed, and oil was noted throughout the engine. The top spark plugs were removed, and the propeller was rotated by hand. Camshaft, crankshaft, and valve train continuity were confirmed to the rear accessory section. Thumb compression was attained on all cylinders. The engine-driven fuel pump was removed from the engine. Several drops of fuel were recovered from the pump. When the pump was actuated by hand, suction and compression were confirmed at the inlet and outlet ports. The electric fuel pump activated when connected to a battery.

The throttle and mixture cables remained attached to the carburetor. The carburetor was disassembled, and its float and needle were intact. The carburetor inlet screen was absent of contamination. The carburetor bowl contained a mixture of fuel and water, consistent with its submersion in the marsh. The oil filter was opened, and no contamination was observed. The left magneto remained attached to the engine and produced spark at all four leads when rotated by hand. The right magneto had separated from the engine during impact and did not produce spark when rotated. The right magneto was disassembled, and the plastic housing that secured the breaker points was found fractured, resulting in no gap in the points. The spark plug electrodes remained intact and exhibited normal wear signatures when compared to a Champion Aviation Check-A-Plug chart. The bottom spark plugs exhibited corrosion consistent with submersion in the brackish marsh water.

During the airframe examination, the fuel selector valve would not move when the fuel selector handle was moved. The fuel selector was then removed and partially disassembled for examination. The examination revealed that the fuel selector valve's polymeric insert had fractured and was in a position that provided openings of about 20% to the right main fuel tank inlet and to the engine outlet, instead of the 100% openings that would have been present with an intact polymeric insert. The fuel selector valve was retained and forwarded to the NTSB Materials Laboratory, Washington, DC.

Metallurgical examination of the fuel selector valve revealed that the lower portion of the polymeric insert exhibited fracture features consistent with rotational ductile overstress. Abrasive wear was present on the outer portion of the insert due to contact with burs on the valve housing. (For more information, see the Materials Laboratory Factual Report in the public docket for this accident.)

The State of Connecticut, Office of the Chief Medical Examiner performed an autopsy on the student pilot. The cause of death was reported as blunt trauma.

Toxicological testing was performed by the FAA Bioaeronautical Science Research Laboratory, Oklahoma City, Oklahoma, on samples from both pilots. The results were negative for the student pilot. Positive results for the flight instructor were consistent with the emergency medical treatment that he received after the accident.