N2618WBell 47G-3B-1 · 1966

On February 23, 2024, about 0740 Pacific standard time, a Bell 47G-3B-1, N2618W, was substantially damaged when it was involved in an accident near Garey, California. The pilot received minor injuries. The helicopter was operated as a Title 14 Code of Federal Regulations Part 137 aerial application flight.

According to the pilot, he was about 5 ft above ground level (agl) at an airspeed of 40 knots conducting an aerial application of fungicide on a field when he then initiated a climb to clear a set of power lines. As he increased power for the climb, he noticed the engine out/low rotor audible warning and the engine simultaneously exhibited a loss of power. He performed an autorotation to an off-airport site. During the autorotation the helicopter entered an uncommanded roll to the left. Despite his control inputs, the pilot was unable to arrest the roll and the helicopter impacted terrain in a nose-down, left-side-low attitude. The helicopter came to rest on its right side with substantial damage to the tailboom and main rotor system.

Postaccident examination of the airframe revealed the fuselage exhibited impact damage to the right side. The right skid fractured at the struts and separated from the fuselage. The bubble canopy fractured and separated from the fuselage. The tailboom exhibited a fracture and separation consistent with impact from the main rotor blades.

Postaccident examination revealed the engine remained secured to the airframe by the mounts. Manual rotation of the main engine driveshaft resulted in the rotation of the stage four turbine wheel, confirming continuity of the N2 drivetrain. Motoring the engine by the starter generator resulted in smooth rotation of the compressor rotor, confirming continuity of the N1 drivetrain. Engine control continuity was confirmed from the throttle to the fuel control unit. All engine oil and fuel lines were found secured with all B-nuts being at least hand tight and with no evidence of leakage.

A check of the pneumatic system by application of about 25 psi of air pressure at the Pc filter resulted in the detection of minor air leakage at both B-nuts on both ends of the accumulator and a large leak at the PTG to FCU Pc input line. Closer examination revealed the B-nut had no thread engagement and had slid aft down the Pc line, as shown in figure 1. The input union on the FCU exhibited evidence of green colored torque paint that was similar in color to the other B-nuts and inputs on the FCU.

Figure 1. Image of the accident fuel control, showing the B-nut, the flared end of the Pc line, and the threads of the attachment fitting of the fuel control.

According to Rolls-Royce, the engine manufacturer, the Pc line connecting the PTG to the FCU is the third of three Pc lines in the system. Pc air is the power supply or motive force that allows the fuel control to modulate fuel delivered to the engine fuel nozzle. With this line disconnected, the engine would reduce power to an unpowered static-state or sub-idle condition.

Further examination of the fuel control, fuel governor, and fuel nozzle revealed normal operation. No other preaccident mechanical malfunctions or failures with the engine or airframe were found that would have precluded normal operation.

According to maintenance records, on June 23, 2023, the fuel control was installed on the accident engine along with several other engine components, including the fuel pump, governor, fuel nozzle, bleed control assembly, and a tachometer generator.

On February 8, 2024, about 15 days before the accident, at a Hobbs time of 902.5, a maintenance facility completed the 150-hour/300-hour engine inspections, along with several airframe inspections. According to the Rolls-Royce Alternate Inspection Schedule, the 150/300-hour inspection states, in part, “Inspect all B-nuts for application and alignment of torque paint. If missing, loosen the B-nut, retighten, and apply torque paint.” The Hobbs meter at the time of the accident read 931.7. The maintenance technician who signed off the work did not recall the specifics of the annual inspection conducted on February 8, 2024, as he did several inspections during the shift, but did report the use of the checklists for each inspection.

Rolls-Royce released commercial service letter (CSL) 2373 that addressed a special tool to access the subject B-nut. The CSL provides details on how to manufacture the tool locally and the tool is also available for purchase.