N34VFCessna P210N · 1979

On January 29, 2018, about 1650 eastern standard time, a Cessna P210N airplane, N34VF, was substantially damaged when it was involved in an accident near Farmington, Pennsylvania. The commercial pilot received minor injuries. The airplane was operated as a Title 14 Code of Federal Regulations Part 91 business flight.

The pilot reported that, while in cruise flight at 8,000 ft mean sea level in snowy conditions, the airplane suddenly felt "heavy," the airspeed decreased, and the tachometer indicated 0 rpm. The pilot declared an emergency, switched fuel tanks, turned on the fuel pump, and attempted to restart the engine, but engine power was not restored. He stated that the propeller did not "budge" and was not windmilling. The controller provided vectors to Nemacolin Airport (PA88), Farmington, Pennsylvania, but the pilot stated that he had no chance of reaching the airport.

The pilot stated that the airplane broke out of the clouds about 300 ft above ground level over a valley. He turned the airplane toward a small field and attempted to land, but while on final approach, the airplane contacted several trees and a power line, shearing off part of the left wing before the airplane impacted the ground and skidded to a stop. The fuel tanks were breached during the impact, which resulted in a fire that enveloped the airplane as the pilot egressed.

At the time of the accident, the airplane had flown 21 hours since its most recent annual inspection, which was completed on November 17, 2017. During the last annual, the Nos. 1 and 2 cylinder assemblies were removed and replaced with new units, including new valves and rings. No irregularities were noted in the logbook and the airplane was returned to service.

The engine was operating under an oil analysis program. An oil and filter change with a subsequent oil analysis was conducted on January 12, 2018. Examination of data from the five the previous oil analyses conducted over the 13 months before the accident showed elevated levels of iron, chromium, silicon, and nickel when compared to the initial sample, taken on October 6, 2016. A note in the most recent oil analysis report stated that the excess metal was likely coming from the "two cylinders that were just replaced" and there was an assumption that "lingering" metal from poor wear and a "break-in" period may have contributed to the excess metal detected. The metals found are present in the drive gear’s alloy steel.

The pilot stated that, several years before the accident, the airplane had a propeller strike and underwent a propeller strike inspection, but no records detailing the maintenance work were found and the maintenance facility that performed the work was no longer in business.

At the time of the accident, the airplane had flown 21 hours since its most recent annual inspection, which was completed on November 17, 2017. During the last annual, the Nos. 1 and 2 cylinder assemblies were removed and replaced with new units, including new valves and rings. No irregularities were noted in the logbook and the airplane was returned to service.

The engine was operating under an oil analysis program. An oil and filter change with a subsequent oil analysis was conducted on January 12, 2018. Examination of data from the five the previous oil analyses conducted over the 13 months before the accident showed elevated levels of iron, chromium, silicon, and nickel when compared to the initial sample, taken on October 6, 2016. A note in the most recent oil analysis report stated that the excess metal was likely coming from the "two cylinders that were just replaced" and there was an assumption that "lingering" metal from poor wear and a "break-in" period may have contributed to the excess metal detected. The metals found are present in the drive gear’s alloy steel.

The pilot stated that, several years before the accident, the airplane had a propeller strike and underwent a propeller strike inspection, but no records detailing the maintenance work were found and the maintenance facility that performed the work was no longer in business.

The airplane came to rest about 300 ft from where it initially impacted trees and power lines, and a debris field containing several pieces of the airplane extended to the main wreckage, which was consumed by fire. The engine was separated from the airframe, but remained attached to the firewall and engine mounts.

The propeller hub remained secured to the crankshaft's propeller flange. All three blades (composite/wood) were fractured about 15 inches out from the propeller hub. The engine sustained thermal damage to the rear accessory section near the firewall, but otherwise remained intact. There were no external anomalies with the engine or engine-related systems that would have precluded normal operation.

The magnetos remained attached to the engine with no slipping noted when manually manipulated. When placed on a test bench, the magnetos produced spark and functioned normally. The top spark plugs appeared to have normal wear with no sign of lead or carbon fouling that would preclude normal operation.

The fuel system, including fuel lines, fuel pump, nozzles, and the throttle body revealed no anomalies; however, when the fuel pump was removed from the engine, damage to the camshaft gear was observed. The oil sump on the bottom of the engine was removed and contained crankshaft gear teeth and metal.

The crankshaft gear was missing most of its teeth and the remaining teeth were damaged. (see Figure 1.) The gear was removed from the crankshaft and there was no sign of fretting between the mating surfaces. There were no additional pre-accident anomalies noted with the crankshaft, counterweights, or connecting rods. All items appeared to be well lubricated with no signs of thermal distress. Removal and examination of the camshaft showed no pre-accident anomalies with the lobes or lifters, but the camshaft gear teeth sustained mechanical damage.

Figure 1. Crankshaft gear damage.

The crankshaft drive gear, camshaft, timing gear, fractured teeth, and metal debris were sent to the NTSB Materials Laboratory for additional examination. The crankshaft drive gear exhibited features such as crack arrest marks and heat tinting, consistent with fatigue cracking before the final fracture. The crack arrest marks and fatigue striations were consistent with inward crack propagation from the tooth edge located near the thread root. There were ratchet marks present near the initiation side of the crack, consistent with multiple fatigue crack initiation sites. Outside of the fatigue cracking region, the fracture surface exhibited a dimpled rupture, consistent with subsequent overstress fracture. A hardness test was performed, and the results indicated that the crankshaft gear was within the typical limits of case-hardened alloy steel.

The cylinders all remained attached to their respective locations on the crankcase and revealed no external anomalies; however, further examination revealed valve impact marks (scallops) on each of the six pistons, as shown in Figure 2.

Figure 2. Piston No. 3 "scallop" impact marks from the valves at the 9:00 and 3:00 o'clock position. All 6 pistons exhibited similar signatures.

Disassembly of the engine revealed no signs of fretting on the mating surfaces and all main bearings remained in place with their lock tabs engaged within the lock slots. There were no pre-accident anomalies noted with the case or the main bearings and all the surfaces appeared well lubricated.

According to the pilot, following his landing he taxied toward a fixed based operator during night, visual meteorological conditions. As he entered a general aviation parking ramp, the right main landing gear struck an unlit and unmarked helicopter dolly. The right landing gear collapsed, the right wing deformed during the collision with pavement, and a fuel leak resulted. The pilot reported that he did not see the dolly prior to the collision, and that there were no mechanical malfunctions or failures of the airplane. The pilot and the Federal Aviation Administration inspector who responded to the accident reported that the helicopter dolly was unlit and unmarked.