N561CPiper PA 46-350P · 2002

On October 9, 2013, about 1000 eastern daylight time, a Piper PA-46-350P, N561C, was substantially damaged during landing when it departed the side of the runway and the nose wheel collapsed at the Greene County – Lewis A. Jackson Regional Airport (I19), Xenia, Ohio. The pilot and passenger on board the airplane were not injured. The airplane was owned and operated by a private individual under the provisions of the 14 Code of Federal Regulations Part 91 as a personal flight. Visual meteorological conditions prevailed at the time of the accident, and an instrument flight plan was filed. The airplane departed Auburn, Alabama, about 0800.

The pilot reported that when the nose wheel touched the runway, the airplane was pulled quickly to the left. He applied right brake and pulled back on the yoke, but the airplane continued to veer off the left side of the runway. The airplane traveled about 500 feet before the nose gear collapsed back into the wheel well, and the airplane's nose and propeller impacted the ground. The propeller blades were bent aft, and the bottom cowling, firewall, engine mounts, and nose gear were crushed upward, and bent aft.

The postaccident examination of the airplane revealed that the engine mount in the area of the nose gear actuator feet was fractured. As a result of similar accidents with Piper models PA-46-310, PA-46-350P, and PA-46R-350T airplane's, Piper Aircraft issued a Mandatory Service Bulletin (SB) No. 1103S on February 2, 2011.

The airplane was a Piper PA-46-350P, serial number 4636326, manufactured in 2002. The airplane's maintenance records indicated that the last annual maintenance inspection was performed on October 26, 2012, with a total aircraft time of 1,064.2 hours. The Piper SB 1103D was complied with on October 12, 2012. The inspection on October 12, 2012, was the only entry in the maintenance records that indicated that SB 1103D had been complied with. The airplane had 1,058 total hours at the time, which was 81 hours before the accident occurred. According to the SB 1103D, the inspection interval for the airplane (serial number 4636326) was:

"Upon reaching 290 hours time in service on the currently installed engine mount, initial inspection to coincide with the next regularly scheduled maintenance record. Thereafter, compliance to be accomplished on a recurring basis, at a frequency interval not to exceed one hundred (100) hours time in service."

The purpose of SB 1103D was to determine if cracks had developed on the engine mount in the area of the nose gear actuator attach feet. The SB stated the following inspection instructions:

1. Clean the engine mount actuator attach feet area.

2. Remove the paint or Dinitrol AV8, if the paint was previously removed and covered with Dinitrol AV8, from the inspection area (reference Figure 1).

NOTE: Paint must be removed using chemical processes only. The use of abrasives or other mechanical methods to remove the paint will hide the existence of any cracks, making an accurate inspection impossible. Use isopropyl alcohol to wipe clean the area of the engine mount where paint was removed.

3. Perform fluorescent penetrant inspection of the nose gear actuator attach feet for cracks per AC 43.13-1B, Chapter 5, Section 5. Inspect the surfaces identified in Figure 1, with specific emphasis on welded areas.

4. If a crack is discovered, the engine mount must be replaced prior to further flight (refer to Table 1).

5. If no cracks are found, continue the repetitive inspection per the compliance time above.

6. Clean the feet and apply a two-coat corrosion prevention compound (CPC) to the area where the paint was removed. This two-coat CPC consists of Dinitrol/Ardrox AV8 as a primer coating and (after the AV8 has dried) Dinitrol/Ardrox AV30 as a top coating.

7. Make an appropriate logbook entry of compliance with this Service Bulletin for each repetitive inspection.

The engine mount was sent to the National Transportation Safety Board's Materials Laboratory for examination. Visual examination of the engine mount revealed that the paint around the engine mount attach feet area was only partially removed, and not in accordance to SB 1103D instructions. The microscopic examination of the right foot of the engine mount revealed that there were fracture features indicative of fatigue progression in many areas. It revealed through thickness fatigue in the foot that initiated at the toe of the weld. Additional fatigue progressed along the length of the foot tube outboard to the right edge of the foot above the forward tubes. Mechanical damage in the form of repeated fracture face re-contact and rubbing prevented identification of the fracturing mode in some areas of the engine mount foot. The examination revealed that the fatigue crack was present in the area of the engine mount where the paint had been removed for the inspection specified in SB 1103D.