N7530RRobinson Helicopter R44 · 2003

On January 30, 2018, about 1350 Pacific standard time, a Robinson Helicopter R44, N7530R, was destroyed when it impacted houses near Newport Beach, California shortly after takeoff. The private pilot and two of the three passengers sustained fatal injuries, one passenger sustained serious injuries, and one person on the ground sustained minor injuries. The helicopter was registered to Spitzer Helicopter and was operated by the pilot as a Title 14 Code of Federal Regulations Part 91 personal flight. Visual meteorological conditions prevailed, and no flight plan was filed for the flight, which originated from John Wayne-Orange County Airport (SNA), Santa Ana, California, about 1 minute before the accident, with an intended destination of Catalina Island, California.

The surviving passenger reported that the pilot and all of the passengers met at the pilot's office and planned to fly to Catalina Island for lunch. Following a brief conversation, the pilot drove the passengers to the airport. The passenger stated that, during the drive, the pilot received a phone call during which he appeared to be frustrated. The passenger asked if everything was ok, and the pilot responded everything was fine and he just wanted a different helicopter. Upon arriving at the airport, they all walked to the helicopter and the pilot appeared to conduct a preflight inspection.

The passenger recalled that the pilot never asked any of the passengers about their weights, nor did he assign them seats. After all the passengers boarded the helicopter, they put on the headsets and the pilot started the engine. The passenger stated that the helicopter started to lift up, shimmied a little, and seemed to hover momentarily before it began a gradual climb. As the helicopter continued to climb steadily, in more of a level attitude than the initial lift off, the helicopter suddenly descended straight down nose first and impacted the ground. Following transport to the hospital, the passenger reported to law enforcement that the pilot said "something's wrong" and apologized to the passengers before stating that he could probably "save it."

Surveillance video footage of the takeoff showed the helicopter slightly move forward in a nose low attitude, lift off, rotate left, increase in a nose-low attitude, and yaw to the right. As the helicopter briefly transitioned into a level attitude, it moved momentarily out of view behind a parked airplane. The tailboom of the helicopter became visible shortly after, in an elevated attitude consistent with a nose-low pitch attitude. As the rest of the helicopter became visible, it appeared to be in a slight climbing left turn, remaining in a nose-low attitude. The helicopter briefly descended and appeared to transition into a level attitude before it began a climb. The helicopter continued the climb while transitioning to a nose-low pitch attitude as it traveled out of frame.

A witness adjacent to the accident site reported observing the helicopter "going down quickly diagonally" before it "pulled [the] nose up and appeared to try an auto rotation while it continued to go down." A second witness reported that they observed the helicopter flying on an easterly heading and descending until it impacted two residential houses. The witness reported that they did not see any parts come off of the helicopter prior to the impact.

A review of archived Federal Aviation Administration (FAA) radar data revealed that the helicopter departed SNA on a southerly heading followed by a slight left turn to a southeasterly heading. The data showed that the helicopter climbed to a maximum altitude of 500 ft mean sea level (msl) and traveled along a southeasterly heading for about 13 seconds. The data showed that the helicopter then descended from 500 ft msl to the last recorded target, at 200 ft msl, in 11 seconds. The last recorded radar return was almost directly above the initial impact area. Review of recorded radio transmissions revealed that the pilot did not make any distress calls.

The pilot held a private pilot certificate with a rotorcraft-helicopter rating and a third-class FAA medical certificate issued on July 11, 2016, with no limitations. The pilot reported on the application for the medical certificate 195 total hours of flight experience, of which 25 hours were in the previous 6 months. The pilot's logbooks were not located.

The accident helicopter was a Robinson Helicopter R44, serial number 1295, and was powered by a 235-horsepower Lycoming O-540-F1B5 engine, serial number L-25375-40A. The most recent 100-hour inspection was completed on December 7, 2017, at a Hobbs time of 568.6 hours and an airframe total time of 6,966.3 hours. The most recent annual inspection was completed on June 1, 2017, at a Hobbs time of 383.9 hours, airframe total time of 6,781.6 hours, and engine time since major overhaul of 383.9 hours.

According to representatives from a fixed-base operator located at SNA, the helicopter was refueled with 15.8 gallons of 100 low-lead aviation fuel based on a request to top off the main fuel tank only.

Using the basic empty weight of the helicopter, fuel load, and weights of the occupants and baggage, the helicopter weighed about 2,476 lbs at the time of takeoff with a longitudinal center of gravity (CG) of 93.42 inches. The calculated weight exceeded the published maximum gross weight of 2,400 lbs and the CG was near the forward range noted in the R44 Pilot Operating Handbook.

A review of recorded data from the SNA automated weather observation station, located about 2 miles north of the accident site, revealed that the conditions at 1353 included wind from 210° at 5 knots, visibility 10 statute miles, few clouds at 13,000 ft above ground level (agl), broken cloud layer at 18,000 ft agl, temperature 26°C, dew point -2°C, and an altimeter setting of 29.98 inches of mercury.

The accident helicopter was a Robinson Helicopter R44, serial number 1295, and was powered by a 235-horsepower Lycoming O-540-F1B5 engine, serial number L-25375-40A. The most recent 100-hour inspection was completed on December 7, 2017, at a Hobbs time of 568.6 hours and an airframe total time of 6,966.3 hours. The most recent annual inspection was completed on June 1, 2017, at a Hobbs time of 383.9 hours, airframe total time of 6,781.6 hours, and engine time since major overhaul of 383.9 hours.

According to representatives from a fixed-base operator located at SNA, the helicopter was refueled with 15.8 gallons of 100 low-lead aviation fuel based on a request to top off the main fuel tank only.

Using the basic empty weight of the helicopter, fuel load, and weights of the occupants and baggage, the helicopter weighed about 2,476 lbs at the time of takeoff with a longitudinal center of gravity (CG) of 93.42 inches. The calculated weight exceeded the published maximum gross weight of 2,400 lbs and the CG was near the forward range noted in the R44 Pilot Operating Handbook.

The helicopter impacted multiple residential structures and a residential street about 0.95 nm miles south-southeast of the departure end of runway 20R at SNA. The initial impact point was identified by damage to the roof of a single-story home. The tail rotor gearbox and one tail rotor blade were located on top of the roof of a single-story home, partially lodged within a hole in the roof. The empennage and opposing tail rotor blade were located between the two homes, surrounded by thick vegetation. Additional impact damage was observed to a palm tree located between the homes.

Numerous impact gouges and paint transfer marks were located on the street in front of both homes, consistent with fuselage and main rotor blade impact. The helicopter came to rest on its left side against a single-story home on a heading of about 189° magnetic, about 86 ft from the first identified point of impact. Throughout the wreckage debris path, plexiglass fragments, clay roofing material, palm tree fragments, and portions of both main rotor blades were observed.

The empennage and the aft section of the tailcone were separated from the airframe. The empennage was separated from the tailcone. The tail rotor gearbox was separated from the empennage and tailcone. The skids were detached and folded underneath the wreckage. The forward section of the tailcone was bent forward almost 180°.

The forward tail rotor drive shaft flex coupling was intact. The intermediate flex coupling was distorted and detached at one arm. The tail rotor drive shaft was separated into multiple sections. The tail rotor drive shaft damper assembly was detached from the tailcone and the tail rotor drive shaft bearing. The bearing rotated freely. The friction at the damper linkage was normal. The aft flex coupling was detached at the tail rotor gearbox yoke input arms. The tail rotor gearbox rotated freely and contained oil. The slider bearing rotated freely. One of the tail rotor blades was separated and distorted. The opposing blade remained attached and exhibited leading edge damage.

The drive belts remained intact and in place within their respective grooves. The sprag clutch operated normally. The belt tension actuator was intact and when operated, the belt tension actuator extended and contracted. Both the upper and lower actuator bearings rotated freely.

The main rotor blades remained attached to the hub. Both main rotor blades were intact. One of the rotor blades was bent upward about mid-span and exhibited slight bending opposite of the direction of rotation near the blade tip. A portion of the blade honeycomb skin structure was torn away from the spar at the blade tip. The opposing main rotor blade exhibited dents and scuffs about 10 inches outboard of the hub. The blade was bent downward about 135° about 2 ft outboard of the hub. The blade was also bent upward mid-span and bent aft opposite of the direction of rotation along the outboard third of the blade. A portion of the blade honeycomb skin structure was torn away from the blade tip.

Dents observed in the oil cooler were consistent with impact from the starter ring gear. At the upper belt sheave, score marks consistent with rotational contact from adjacent components were observed.

Flight control continuity was established throughout the helicopter from the cockpit controls to the main rotor and tail rotor controls through various overload fractures.

The engine remained attached to the airframe. The upper spark plugs were removed. The electrodes were undamaged and exhibited color consistent with normal operation with the exception of the No. 3 spark plug, which was oil-soaked. The engine crankshaft was rotated using the cooling fan. Compression and suction were obtained on all six cylinders.

The oil sump screen was removed and contained two small plastic fragments consistent with the magneto drive bushings. The oil filter was removed and cut open. The internal filter element exhibited no debris.

The engine was installed on a test stand. In order to facilitate an engine run, a slave starter and propeller were installed. The engine was started and ran uneventfully. During the engine run, the No. 3 cylinder was not producing any exhaust gas temperature (EGT) readings on the engine monitoring unit installed on the test stand. The engine was shut down and further inspected. The bottom spark plug lead of the No. 3 cylinder was found impact damaged, and the upper spark plug lead was pulled away from the ignition cap. A serviceable ignition harness was installed for both the left and right magnetos. The engine was started a second time and operated throughout various power settings. At maximum power, the engine produced 2,600 rpm at 29 inches of manifold pressure. Engine rpm drops during magneto tests were within specification. The engine ran uneventfully until it was shut down using the mixture cut-off.

No evidence of any preexisting mechanical malfunction was observed with the airframe or engine.

For further information, see the Accident Site, Airframe, and Engine Examination Summary report and Robinson Helicopter's report within the public docket for this accident.

According to the FAA's Helicopter Flying Handbook (FAA-H-8083-21B), Chapter 6, Weight and Balance:

Weight limits are necessary to guarantee the structural integrity of the helicopter, enable pilots to predict helicopter performance and insure aircraft controllability.

Helicopter performance is not only affected by gross weight, but also by the position of that weight. It is essential to load the aircraft within the allowable CG range specified in the rotorcraft flight manual's (RFM) weight and balance limitations. Loading outside approved limits can result in insufficient control travel for safe operation.

The pilot should ensure that the helicopter is properly balanced within its center of gravity limitations, so that minimal cyclic input is required during hovering flight, except for any wind corrections. Since the fuselage acts as a pendulum suspended from the rotor, changing the CG changes the angle at which the aircraft hangs from the rotor…if the CG is too far forward of the mast, the helicopter hangs with its nose tilted down…

The Orange County Coroner, Santa Ana, California, performed an autopsy on the pilot. The autopsy report indicated that the cause of death was multiple blunt force traumatic injuries.

Toxicology testing on specimens recovered from the pilot performed at the FAA Forensic Sciences Laboratory identified unspecified amounts of Irbesartan in the blood and urine.

Irbesartan is a prescription medication used alone or in combination with other medications to treat high blood pressure. It is not considered to be impairing.