N911SZ is a Bell UH-1H. It is a rotorcraft with 15 seats. The registration is active, with the registrant based in Albuquerque, NM. It has been registered to its current owner since May 2000. This page also carries 1 NTSB event.
2000
That's everything on file so far — TailWiki checks the FAA registry daily and adds new entries as N911SZ's record changes.
On July 16, 2022, about 1920 mountain daylight time, a Bell UH-1H, N911SZ, was substantially damaged when it was involved in an accident near Chapelle, New Mexico. The pilot, two tactical flight observers, and the rescue specialist sustained fatal injuries. The helicopter was operated as a Title 41 United States Code public aircraft flight.
After completing several firefighting missions in support of the New Mexico Forestry Division, the helicopter was fueled at Las Vegas Municipal Airport (LVS), Las Vegas, New Mexico. The helicopter departed LVS about 1838 and flew to the dip site/staging area, operated at the firefighting location, then flew back to the staging area where the remainder of the crew was loaded for the return flight to Double Eagle II Airport (AEG), Albuquerque, New Mexico.
About 1915, the helicopter departed the staging area to the west. The last automatic dependent surveillance-broadcast (ADS-B) data, recorded at 1920, showed the helicopter about 0.5 mile east of the accident site. The helicopter was level, 500 to 600 ft above ground level on a westbound course with a groundspeed of 133 knots (kts).
Onboard flight data indicated that, at 1920:01, the helicopter entered a 484 ft-per-minute (fpm) descent at a groundspeed of 133 kts. The helicopter subsequently began to descend rapidly, and at 1920:13, the last recorded flight data indicated a descent rate of 5,433 fpm and groundspeed of 102 knots.
Two witnesses observing the sunset from a ridge about 0.5 mile east of the accident site reported that the helicopter flew past their location westbound, then rapidly descended without making any turns. After the helicopter impacted the ground, a large plume of dust was observed. (See photo 1.)
Photo 1. Accident Site Area with Dust from Helicopter (provided by witness)
A pilot previously in the unit stated that the accident pilot had accomplished annual flight training at HeliStream, which included autorotation training with turns and touchdowns. This information was consistent with a review of the accident pilot’s logbook.
The accident pilot’s last annual training was flown in a Eurocopter AS350. A review of flight records indicated that the accident pilot had not recently conducted emergency flight training in a UH-1.
The helicopter was powered by an Ozark Aeroworks engine (formerly Honeywell, AlliedSignal, and Textron Lycoming) and was of a conventional design, with a two-bladed main rotor and a two-bladed tail rotor mounted on a tail boom.
The Bernalillo County Sheriff’s Department purchased the helicopter from the US Army on March 11, 1999. It was registered as a government aircraft on March 9, 2000.
Around the time of the accident the sun’s elevation was about 6.4° and the azimuth was about 291°.
The helicopter was powered by an Ozark Aeroworks engine (formerly Honeywell, AlliedSignal, and Textron Lycoming) and was of a conventional design, with a two-bladed main rotor and a two-bladed tail rotor mounted on a tail boom.
The Bernalillo County Sheriff’s Department purchased the helicopter from the US Army on March 11, 1999. It was registered as a government aircraft on March 9, 2000.
The wreckage was located in high southwestern desert terrain that was populated with scrub juniper bushes. (See photo 2.) The initial impact was identified by disturbed ground in the shape of the helicopter tail and fuselage. The tailboom was crushed and the tail skid “stinger” was bent upwards significantly, consistent with very hard contact with the ground.
The tail boom separated from the main fuselage, both of which were located about 122 ft west of the initial impact. The main rotor was about 40 ft to the left of the main wreckage, with the main rotor mast fractured immediately below the hub. One main rotor blade was minimally damaged and the other blade was fractured at the spar. The main rotor blade grips had minimal damage.
Photo 2. Wreckage at the accident Site
Examination revealed continuity of the rotor drive and flight control systems, and no anomalies were observed with the hydraulic or fuel systems.
A minimal amount of foreign debris, primarily dirt, was observed in the intake, compressor, gas producer, power turbine (PT), and exhaust sections. The PT rotated freely and no metal spray, scoring, scuffing, tip rub, or bending of the blades was noted.
The N1 tachometer-generator was clean but would not rotate. Removal of the starter- generator revealed that the starter-generator drive shaft and input (zerol) gear were both fractured. The starter-generator turned freely by hand via the remains of the input shaft.
Removal of the N1 accessory gearbox (AGB) magnetic chip detector plug revealed a large quantity of metallic chips on the magnetic tip. Multiple metallic fragments were found in all the bearing compartment oil return/scavenge lines; the supply lines were clean of debris or obstructions. Two helical-cut gear teeth were found in the N1 AGB oil, similar to teeth from the zerol gear. Both teeth exhibited expected wear patterns, with no other damage noted.
Metallurgical examination of the zerol gear revealed multiple fatigue fractures, as well as gouging on both the leading and lagging flanks and lands of the gear teeth. The zerol gear was determined to have failed in fatigue from a crack that formed 90° to the original, progressing across the gear. No material anomalies were observed that would result in the crack initiation.
Engine Chip Event and Oil Sampling
On September 12, 2021, an engine chip event was documented in the engine logbook. BCSO maintenance personnel stated that a precautionary landing occurred following an engine chip light and a small piece of ferrous metal was found on the magnetic chip plug. The corrective actions taken included draining and flushing of the system, as well as removing, cleaning, and reinstalling the filter elements. No further engine chip lights were reported following the engine chip event.
An oil sample and the chip were sent in for analysis, but no laboratory analysis of the chip was obtained by maintenance personnel to troubleshoot the chip event. The helicopter flew about 17 hours between the chip event and the accident.
The maintenance manual for the accident engine included oil sampling and testing for wear metals, including silicon, aluminum, chromium, copper, iron, magnesium, nickel, silver, and titanium. The maintenance manual stated that the values were not “go/no-go” criteria.
Following the engine installation in 2018, ten oil samples were taken, including the chip event sample.
Between the oil samples taken in May 2020 and April 2021, which involved 232 hours oil life, iron increased from 0.6 part per million (ppm) to 1.3 ppm, an average increase of 0.003 ppm per hour of oil life.
Between the oil samples taken in July 2021 and February 2022, which involved 37 hours of oil life, iron content increased from 1.3 ppm to 1.8 ppm, an average increase of 0.0135 ppm per hour of oil life.
The iron content increased 450% in ppm per hour of oil life between the two sampling periods of May 2020 through April 2021 and July 2021 and February 2022.
Main Generator Removal
On March 22, 2017, the main generator and input quill were removed for weight reduction. An “inop” sticker was placed on the main generator voltmeter on the center console. The UH-1 operating manual emergency procedures includes operating solely on the standby or starter-generator in the event the main generator fails, but not continual operation. According to Bell safety personnel, the configuration of a removed main generator had not been evaluated by Bell for adverse effects to component life, to include vibrations.
Zerol Gear History
A review of US Army records did not identify any failures of the zerol gear similar to that found in the accident. US Army maintenance systems did not have installation or overhaul information for the zerol gear, indicating that it was not a tracked part.
Performance Calculations
Density altitude was calculated as 9,059 ft at the helicopter’s cruise altitude. Based on 133 knots groundspeed and reported southeasterly winds at the nearest location, the helicopter’s indicated airspeed at its cruise altitude was calculated to be 100 to 110 kts.
An autopsy of the pilot was performed at the University of New Mexico, Office of the Medical Investigator, Albuquerque, New Mexico. The cause of death was blunt force injuries.
Toxicology testing performed at the Federal Aviation Administration Forensic Sciences Laboratory was negative for all screened drugs and alcohol.
No photos yet. Sign in to add the first one.