N979DCDiamond Aircraft Ind DA20-C1 · 2005

On January 19, 2015, about 1700 eastern standard time, a Diamond Aircraft Inc. DA 20 C1 airplane, N979DC, made a forced landing into a field near Shipshewana, Indiana. The solo student pilot was not injured and the airplane sustained substantial damage. The airplane was registered to and operated by New Horizons Aviation Inc. under the provisions of 14 Code of Federal Regulations Part 91 as a solo instructional flight. Visual meteorological conditions prevailed and no flight plan was filed. The local flight departed from the Goshen Municipal Airport (GSH), Goshen, Indiana about 1645.

According to the student pilot, he was about 1,600 feet above ground level practicing ground reference maneuvers. He reported that the engine operation became erratic and the airplane might have entered an aerodynamic stall. He advanced the throttle to full forward, but the engine did not respond and experienced a total loss of power. He attempted to restart the engine by completing the emergency procedures that he remembered. The engine "turned over" but did not restart. He then prepared for a forced landing into a nearby field. During the base to final turn, he lost control of the airplane and descended to the ground. The airplane impacted the field and continued into a propane tank and then a house where it came to rest.

The student pilot reported having accumulated 12 total flight hours, all of which were logged in the preceding 30 days, and in the same make and model airplane.

The airplane was a two seat, low wing, tricycle landing gear, training airplane which was manufactured in 2005. It was powered by a 125-horsepower Continental Motors Inc. IO-240 engine, which drove a Sensenich two-bladed, fixed pitched, wooden propeller.

On January 22, 2015, the airplane was examined after the accident by a Federal Aviation Administration (FAA) Inspector and a representative from Continental Motors Inc. The examination revealed that the majority of the induction air filter was covered with ice. The alternate air lever in the airplane was OFF. The engine cylinders each displayed normal operating signatures. The spark plugs displayed normal wear signatures when compared to a Champion Aviation Service Manual No. AV6-R. Internal crankshaft continuity was established by rotating the propeller. Additionally, all four cylinders displayed thumb suction and compression. The top spark plugs and ignition leads were reinstalled for an engine operational test run. The air filter remained impacted with ice during the first engine run; the engine was capable of running with the throttle full forward and produced about 2,200 RPM which is normal for a fixed pitch propeller. The alternate air lever was moved to ON and the engine was still capable of producing about 2,200 RPM. The engine was then shut down and the ice removed from the air filter. The engine was subjected to a second test run; the engine produced 2,200 RPM with the throttle advanced to full forward. The ignition switch was actuated to test both magnetos and the decreases in RPM were normal and the engine indications displayed normal operating parameters. Other than the ice in the air induction filter there were no anomalies noted that would have precluded normal operation. The airplane sustained substantial damage to the fuselage and empennage.

During the postaccident investigation, the pilot was asked about the airplane's alternate air lever. He reported that he was unfamiliar with the lever and did not know its intended use. He also stated that he flew through some low clouds during the flight, but they did not obstruct his view of the ground and he was able to maintain visual flight rules (VFR) the entire time.

At 1653 the weather observation station at GSH, which was located 13 miles southwest, reported the following conditions: wind from 200 degrees at 3 knots, visibility 10 miles, few clouds at 12,000 feet, temperature 36° Fahrenheit (F), dew point 30° F, altimeter setting 29.94 inches of mercury.

Using the average temperature lapse rate, 3.5° F per 1,000 feet, the temperature at 1,600 feet would have been about 30° F.

The Diamond Aircraft Airplane Flight Manual (AFM) stated in Chapter 7.9.2 Engine Controls: The alternate air control selects a second induction air intake in case of restriction of the primary air intake (air filter).

AFM Chapter 3.3.1 (c) Engine Failure during Flight – ENGINE RUNNING ROUGHLY – the pilot should perform the following checklist:

1. Mixture – FULL RICH

2. Alternate Air – OPEN

3. Fuel Shut-off – OPEN

4. Fuel Pump – ON

5. Ignition Switch – cycle L – BOTH – R – BOTH

6. Throttle – at present position

7. No Improvement – reduce throttle to minimum required power, land as soon as possible.

FAA Advisory Circular 20-113. The Advisory Circular states that one form of induction system icing is impact ice and states in part:

"Impact ice is formed by moisture-laden air at temperatures below freezing, striking and freezing on elements of the induction system which are at temperatures of 32° F or below. Under these conditions, ice may build up on such components as the air scoops, heat or alternate air valves, intake screens, and protrusions in the carburetor. Pilots should be particularly alert for such icing when flying in snow, sleet, rain, or clouds, especially when they see ice forming on the windshield or leading edge of the wings. The ambient temperature at which impact ice can be expected to build most rapidly is about 25° F, when the super cooled moisture in the air is still in a semi liquid state. This type of icing affects an engine with fuel injection, as well as carbureted engines. It is usually preferable to use carburetor heat or alternate air as an ice prevention means..."